| Content |
The new Classic Evo is based on the successful EISA Award winner The Classic and the experience Pro-ject won designing and building their icon turntable, the 175 VPO. The main improvement is the sub-platter, where they used the experience they gained from designing the Vienna Philharmonic Recordplayer to add key changes to the Classic Evo, adding performance features that are rarely seen in this price category. For improved comfort, an electronic speed change was built in, which lets you switch from 33 to 45 rpm (and vice versa) with the push of a button.
Compared to the old Classic, we improved the subchassis; we tried to make it heavier and stiffer to reduce resonances. Isolating the platter and tonearm from the resonances of the motor and main plinth is the target.
Platter & sub-platter
The heavy aluminium main platter construction utilises advanced thermoplastic elastomers (TPE*) for optimising resonance behaviour. A drawback for most of the old designs was the platter. Casted platters all have been heavy (which is good for speed constancy and low wow and flutter) but suffered very much from ringing effects which again caused colouration of the sound. The platter of The Classic Evo is precisely machined out of a special aluminium alloy again damped with TPE*, which offers special damping abilities. The main bearing construction we use is a similar system as the one on the Vienna Philharmonic Record player.
The diamond-cut precision alu sub-platter, like in the limited edition Vienna Philharmonic Recordplayer, enables much improved tolerances. This extraordinarily sophisticated part is accurately machined and guarantees very good isolation between bearing noise and the platter itself.
New carbon/aluminium tonearm
The radical new designed Classic tonearm is the result of 25 years of experience in mechanical construction. The tonearm tube is made out of a sandwich of carbon and aluminium: carbon for stiffness and speed, alu for better damping. The bearing has been upgraded to the same type that is used on our Pro-Ject CC EVO tonearms. It facilitates frictionless vertical and horizontal movement, guaranteeing precise tracking across the entire duration of the record. The counterweight incorporates a TPE* damper which allows us to reduce the amplitude of the tonearm cartridge resonance frequency by 50%. As typical for Pro-Ject and absolutely not standard at that price range we offer also azimuth and VTA adjustment to use a variety of cartridges.
MC Cartridge
We supply as standard the Ortofon Quintet Red moving coil cartridge. However, as the tonearm offers excellent damping and flexibility as well, its effective mass can be called middle heavy, so it is also a very good partner for MC cartridges. As the Classic is a wonderful state of the art deck, we decided to use an MC cartridge to use the potential of the player. MC cartridges are expensive, but the better choice. They are rarely used at such a price point. Pro-ject is therefore convinced to offer you an unbeatable price-performance package.
Features:
- Diamond cut precision alu sub-platter
- Improved sandwich subchassis
- Ortofon Quintet Red cartridge pre-installed
- Electronic speed control (33/45 rpm)
- Belt drive with electronic speed control 33/45 rpm
- Height adjustable decoupling feet
- Precision balanced TPE-damped aluminium-platter
- Metal/MDF sandwich chassis floating on TPE suspension
- 9” carbon/aluminium tonearm with MM & MC capability
- Inverted EVO bearing design with four ABEC7 spec ballraces
- Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances
- Azimuth and VTA fully adjustable
- TPE damped counterweight
- Classic wooden chassis in 2 satin finishes (walnut, eucalyptus)
- Dustcover included
|
The single speed RP78 has been designed and engineered to achieve outstanding performance way beyond the expectations of a product at this price point. Using our latest 24v motor technology the new Planar 78 is also fitted with the latest RB220 precision tonearm.
Designed solely for the reproduction of 78 rpm records, we have omitted any unnecessary gimmicks allowing us to concentrate the manufacturing costs on the high-quality parts necessary to reproduce records accurately. The minimalist design of the Rega Planar 78 and the use of extremely high-quality components ensure that your turntable should last for many years.
The RB220 offers astonishing performance and is one of Rega's best selling tonearms. An evolution of the famous RB250, which was supplied as standard on early Planar 2 and P2 turntable, the RB220 uses our patent-pending ultra-lightweight high-quality polymer bearing selected, high quality vertical and horizontal bearings.
The tonearm uses our die-cast tube and the three-point fixing technique based on the mounting design system. This system reduces stress on the plinth and tonearm and offers greater stability though the arm. All of which translates into more music for you the listener.
Details & Specs:
- Hand-assembled RB220 Rega tonearm.
- Precision main bearing.
- Flywheel effect platter manufactured from phenolic resin which assists startup speed and stability.
- Lightweight plinth.
- Low vibration 24v motor.
|
The VT-E turntable proves that turntable setup doesn’t have to be rocket science. This great sounding belt-driven deck even comes in two separate versions for both left- and right-handed users. The VT-E can be positioned either free-standing on a table or wall-mounted using the included low-profile metal bracket. Installation is a breeze since everything is pre-adjusted out of the box – tracking and anti-skating force are carefully set so no further set-up needed! Sse both Bluetooth and RCA output at the same time.
Speed:
33 & 45 rpm (manual speed change)
Drive principle:
Silicone belt drive
Speed variance:
0.8% @ 33 rpm, 0.7% @ 45 rpm
Wow & flutter:
0.29% @ 33 rpm, 0.27% @ 45 rpm
Signal to noise ratio:
-65 dB
Platter:
300 mm composite wood (1.8 lb.) w/felt mat
Main bearing:
Stainless steel
Tonearm:
8.6” aluminum
Effective tonearm length:
218.5 mm
Overhang:
22.0 mm
Effective tonearm mass:
8.0 g
Compatible cartridge weight:
3.0 - 5.5 g (Otrofon OM5E included) 0 - 2.5 g (pre-adjusted at 1.8 g)
Tracking force range:
0 - 2.5 g (pre-adjusted at 1.8 g)
Included accessories:
power supply, record clamp
Power consumption:
4.5 W
Dimensions (free-standing):
16.9” x 13.6” x 9.6” (W x H x D)
Dimensions (wall mounted):
16.9” x 12.2” x 5.1” (W x H x D)
Weight:
6.2 lbs. (net)
|
The MMF-5.3 turntable is a 2-speed belt driven audiophile turntable employing the unique dual-plinth construction originated by Music Hall.
- Counterweight's center of gravity is level with the stylus tip, is decoupled from the arm, and acts as a resonance damper.
- DC synchronous motor for superior speed stability separately isolated on the lower platform.
- Includes properly aligned and pre-mounted Ortofon 2M Blue cartridge with a replaceable nude elliptical diamond stylus.
- Dynamically balanced alloy platter with soft felt mat.
- Dust cover and 45 rpm adaptor included.
| The new Planar 2 was developed over the past two years alongside the recently released Planar 3. Featuring the brand new RB220 tonearm which is packed with groundbreaking new features such as a new 24v low noise motor, acrylic laminated plinth, newly designed central bearing and so much more. Every feature of this innovative new turntable is designed to extract the maximum amount of information and detail from your vinyl collection.
- Re-designed feet - New improved foot assembly to increase stability and reduce vibration transfer.
- Carbon cartridge - supplied as standard on all Planar 2's for simple plug and play convenience.
- Motor cover tray - with integrated cooling.
- Optional lid / plinth protectors - supplied to prevent marks on the plinth and keep it looking its best.
- Instructions - Easy to use multi-lingual quick start guide for easy set up.
- Packaging - New improved packaging.
- Tonearm: Hand-assembled RB220 tonearm
- Cartridge: Factory fitted Carbon moving magnet cartridge
- Motor: 24 V low noise motor
- Dimensions (lid closed) (W x H x D): 447 x 117 x 360 mm
- Weight: 5.5 kg
| Thanks to extensive research and development, we have now elevated our classic RPM design to an even higher level. The RPM 10 Carbon uses a new extra-heavy chassis which features a special CNC-machined MDF base with resin-coated steel pellets to form an extra-heavy and precise sandwich construction. A special, complex heat treatment and carbon surface coating ensures superior low resonance levels. The mass-loaded chassis is effectively decoupled from its surface using magnetic feet. Combined with a new special polished aluminum platter with internal TPE damping and a vinyl layer on top, the inverted ceramic main bearing delivers an absolutely stable turntable speed with extra-low rumble due to the magnetic suspension of the platter. The heavy outboard motor unit is equipped with precise motor control and features a built-in switch between 33 & 45 rpm. Last but not least, the no-compromise 10" EVO tonearm with conical carbon-fiber arm tube and inverted bearing design ensures perfect tracking, even with demanding cartridges. Highly flexible, top-grade copper internal wiring is used. The RPM 10 Carbon is delivered with Ground it Carbon equipment base and top-grade 5P phono cable "Connect It CC" with RCA plugs (XLR as an option). An acrylic dust cover, "Cover it 1", is also available.
Specifications
Speed: 33, 45 rpm (electronic speed change)
Drive: Belt drive
Platter: 10.4 kg aluminum (300mm diameter)
Main Bearing: inverted stainless steel with ceramic ball/plate
Wow & Flutter: 33 +/- 0.11% 45: +/- 0.10%
Speed Drift: 33: +/- 0.01% 45: +/- 0.01%
Signal to Noise: -75dB
Tonearm: 10" Carbon EVO
Effective Arm Length: 254 mm
Effective Arm Mass: 8.5 g
Overhang: 16mm
Tracking Force: 10 - 35mN
Supplied Counterweights: 5 - 7.5g / 7 - 10g / 9 - 11g / 10 - 14g
External Power Supply: 15 volts DC / 1.6A
Power Connection: 110/120 or 230/240 Volt - 50 or 60 Hz
Power Consumption: 15 watts max |
Reviews
There are no reviews yet.