| Content |
In 1991 Pro-Ject started a revolution in HiFi with the introduction of the Pro-Ject 1 turntable. A new high-end, low budget turntable at a time when CD was king. Against all odds, we were creating interest in analog audio at a time when others were turning their backs, and the success was only down to three critical philosophies: Simple yet technically correct design, High-quality valuable materials, and Fully handcrafted, expert engineers, made in the EU.
The design is carefully tuned to offer the most critical features for the best price and everything is put together with Pro-Ject‘s decade long experience in making the best performing turntables without blowing the budget: MDF is 2-3 times more expensive than standard particle boards, not to mention a plastic chassis, but sounds and feels way better.
The X1‘s luxury 8 layers of painting and the hand-polished finish are 3-4 times more expensive than simple foils.
Inside, it houses a sophisticated DC/AC generator board which, combined with the convenient speed control board, delivers clean and stable power to the quiet-running motor. This adds additional cost but performs many times better than a simple, direct powered AC motor. For even further improved performance, the motor is decoupled from the main plinth using a new motor suspension system.
In the X1, the motor drives a new, heavy, non-resonant Acryl platter via a sub-platter drive system and a premium grade main bearing for liquid smooth rotation. This is the perfect platform on which to place your precious vinyl records, guaranteeing absolute reliability in its performance and sonic character. The X1 is also better than its predecessors thanks to the super-stiff, perfectly tempered Carbon/Alu sandwich construction tonearm. This new 8.6” tonearm design is incredibly light and stiff, with improved resistance to external interference. Finished as a one-piece, with no resonance-inducing headshell, the X1 can also be set for azimuth and VTA adjustment, offering the flexibility that so many people are asking for, especially in this and even lower price ranges.
The tonearm is then supplied with a TPE-damped counterweight, further reducing cartridge-tonearm resonances.
Lastly, height-adjustable feet in their Alu/ TPE sandwich construction are a very exclusive but necessary feature to level up the turntable and effectively isolate it from the surface it is place on.
The X1 has all the high-end features of modern turntable designs to maximize the music and listening experience. All these features can in fact be done at a reasonable cost. Due to our extensive experience and meticulous manufacturing processes, we put resources, time and effort into giving music lovers the best sound for their money, rather than cutting corners to save on costs. It is a statement and a counterpoint against other upcoming turntable designs, which go the way of offering more features but less performance.
- Speed control with electronic speed switch for ultimate speed stability
- Carefully isolated motor for less vibration and noise
- Sub-platter with extremely low 0.001mm bearing tolerances
- Stainless steel platter-bearing with soft brass bushing and teflon mirrors for lowest rumble and noise, and a stable, accurate speed transmission
- Resonance free, 1.5 kg heavy acryl platter
- 8,6” carbon/alu sandwich tonearm with best internal damping and TPE damped counterweight
- Kardan ultra-low friction 4 pin point precision tonearm bearing
- Sumiko Rainier cartridge newly developed with Sumiko for highly dynamic and full sound
- Massive and heavy, precision CNC‘d MDF chassis
- Luxury 8 layers of painting and hand-polished finish or real-wood, satin-waxed veneer
- Super shielded, semi-symmetrical, low-capacitance phono cables - purpose designed by Pro-Ject
- Height adjustable, aluminum feet for massively reduced risk
of acoustical feedback
- Handmade in Europe
|
The B-Sharp sheds all of the non-essential cosmetic adornments of the C-Major without compromising performance or mechanical integrity, providing vinyl enthusiasts with a superb playback option at a more affordable price.
- Features the new B-Note tonearm, made from a carbon fiber alloy that is light yet rigid with a black anodized aluminum headshell. The B-Note tonearm provides all of the key features for cartridge alignment and adjustability: VTA (Vertical Tracking Angle), SRA (Stylus Rake Angle), VTF (Vertical Tracking Force), azimuth and a slotted headshell for overhang / offset angle.
- The anti-skate mechanism has been engineered for more intuitive calibration, making setup of the B-Sharp notably easier than competitive products.
- A proprietary low noise motor, floating chassis, aluminum platter and a high-density MDF low profile base are included as standard features of the B-Sharp. Like the C-Major, the B-Sharp uses a high-tech TPE (thermoplastic elastomers) suspension system that works in concert with adjustable feet that provide levelling ability for the table.
- Comes equipped with a factory installed Ortofon 2M Blue Cartridge, hinged dustcover, low mass aluminum record clamp, and a felt platter mat-all included.
|
The VT-E turntable proves that turntable setup doesn’t have to be rocket science. This great sounding belt-driven deck even comes in two separate versions for both left- and right-handed users. The VT-E can be positioned either free-standing on a table or wall-mounted using the included low-profile metal bracket. Installation is a breeze since everything is pre-adjusted out of the box – tracking and anti-skating force are carefully set so no further set-up needed! Sse both Bluetooth and RCA output at the same time.
Speed:
33 & 45 rpm (manual speed change)
Drive principle:
Silicone belt drive
Speed variance:
0.8% @ 33 rpm, 0.7% @ 45 rpm
Wow & flutter:
0.29% @ 33 rpm, 0.27% @ 45 rpm
Signal to noise ratio:
-65 dB
Platter:
300 mm composite wood (1.8 lb.) w/felt mat
Main bearing:
Stainless steel
Tonearm:
8.6” aluminum
Effective tonearm length:
218.5 mm
Overhang:
22.0 mm
Effective tonearm mass:
8.0 g
Compatible cartridge weight:
3.0 - 5.5 g (Otrofon OM5E included) 0 - 2.5 g (pre-adjusted at 1.8 g)
Tracking force range:
0 - 2.5 g (pre-adjusted at 1.8 g)
Included accessories:
power supply, record clamp
Power consumption:
4.5 W
Dimensions (free-standing):
16.9” x 13.6” x 9.6” (W x H x D)
Dimensions (wall mounted):
16.9” x 12.2” x 5.1” (W x H x D)
Weight:
6.2 lbs. (net)
|
The Cliffwood was made to celebrate the heritage of VPI and to honor the city where their turntables are built. VPI teamed up with Grado Labs to engineer a cartridge shell specifically for the Grado to make it easier to mount and contribute to the sound signature.
- New 9" machined aluminum gimbal tonearm with lateral type bearing.
- 1.25" thick textured vinyl-covered non-resonant MDF chassis. Platter rotates on an oil bath bearing.
|
The MMF-5.3 turntable is a 2-speed belt driven audiophile turntable employing the unique dual-plinth construction originated by Music Hall.
- Counterweight's center of gravity is level with the stylus tip, is decoupled from the arm, and acts as a resonance damper.
- DC synchronous motor for superior speed stability separately isolated on the lower platform.
- Includes properly aligned and pre-mounted Ortofon 2M Blue cartridge with a replaceable nude elliptical diamond stylus.
- Dynamically balanced alloy platter with soft felt mat.
- Dust cover and 45 rpm adaptor included.
|
The single speed RP78 has been designed and engineered to achieve outstanding performance way beyond the expectations of a product at this price point. Using our latest 24v motor technology the new Planar 78 is also fitted with the latest RB220 precision tonearm.
Designed solely for the reproduction of 78 rpm records, we have omitted any unnecessary gimmicks allowing us to concentrate the manufacturing costs on the high-quality parts necessary to reproduce records accurately. The minimalist design of the Rega Planar 78 and the use of extremely high-quality components ensure that your turntable should last for many years.
The RB220 offers astonishing performance and is one of Rega's best selling tonearms. An evolution of the famous RB250, which was supplied as standard on early Planar 2 and P2 turntable, the RB220 uses our patent-pending ultra-lightweight high-quality polymer bearing selected, high quality vertical and horizontal bearings.
The tonearm uses our die-cast tube and the three-point fixing technique based on the mounting design system. This system reduces stress on the plinth and tonearm and offers greater stability though the arm. All of which translates into more music for you the listener.
Details & Specs:
- Hand-assembled RB220 Rega tonearm.
- Precision main bearing.
- Flywheel effect platter manufactured from phenolic resin which assists startup speed and stability.
- Lightweight plinth.
- Low vibration 24v motor.
|
Reviews
There are no reviews yet.