| Content | Turntable section
Type Direct: Drive Manual Turntable
Turntable Speeds: 33-1/3, 45 and 78 r/min
Starting Torque :2.2 kg-cm
Build-up Characteristics: 0.7 s. from Standstill to 33-1/3 r/min
Wow And Flutter: 0.025 % W.R.M.S.
Turntable Platter:
- Aluminum diecast
- Diameter : 332 mm (13-5/64 inch)
- Weight: Approx. 2.5 kg (5.51 lb) (Including rubber sheet)
Tonearm Section
Type: Universal Static Balance
Effective Length: 230 mm (9-1/16")
Overhang: 15 mm (19/32")
Tracking Error Angle:
- Within 2° 32' (at the outer groove of 30 cm (12") record)
- Within 0° 32' (at the inner groove of 30 cm (12") record)
Offset Angle: 22°
Arm-height Adjustment Range: 0 - 6 mm
Stylus Pressure Adjustment Range: 0 - 4 g (Direct Reading)
Head Shell Weight: Approx. 7.6 g | The new Planar 2 was developed over the past two years alongside the recently released Planar 3. Featuring the brand new RB220 tonearm which is packed with groundbreaking new features such as a new 24v low noise motor, acrylic laminated plinth, newly designed central bearing and so much more. Every feature of this innovative new turntable is designed to extract the maximum amount of information and detail from your vinyl collection.
- Re-designed feet - New improved foot assembly to increase stability and reduce vibration transfer.
- Carbon cartridge - supplied as standard on all Planar 2's for simple plug and play convenience.
- Motor cover tray - with integrated cooling.
- Optional lid / plinth protectors - supplied to prevent marks on the plinth and keep it looking its best.
- Instructions - Easy to use multi-lingual quick start guide for easy set up.
- Packaging - New improved packaging.
- Tonearm: Hand-assembled RB220 tonearm
- Cartridge: Factory fitted Carbon moving magnet cartridge
- Motor: 24 V low noise motor
- Dimensions (lid closed) (W x H x D): 447 x 117 x 360 mm
- Weight: 5.5 kg
|
The MMF-5.3 turntable is a 2-speed belt driven audiophile turntable employing the unique dual-plinth construction originated by Music Hall.
- Counterweight's center of gravity is level with the stylus tip, is decoupled from the arm, and acts as a resonance damper.
- DC synchronous motor for superior speed stability separately isolated on the lower platform.
- Includes properly aligned and pre-mounted Ortofon 2M Blue cartridge with a replaceable nude elliptical diamond stylus.
- Dynamically balanced alloy platter with soft felt mat.
- Dust cover and 45 rpm adaptor included.
|
The B-Sharp sheds all of the non-essential cosmetic adornments of the C-Major without compromising performance or mechanical integrity, providing vinyl enthusiasts with a superb playback option at a more affordable price.
- Features the new B-Note tonearm, made from a carbon fiber alloy that is light yet rigid with a black anodized aluminum headshell. The B-Note tonearm provides all of the key features for cartridge alignment and adjustability: VTA (Vertical Tracking Angle), SRA (Stylus Rake Angle), VTF (Vertical Tracking Force), azimuth and a slotted headshell for overhang / offset angle.
- The anti-skate mechanism has been engineered for more intuitive calibration, making setup of the B-Sharp notably easier than competitive products.
- A proprietary low noise motor, floating chassis, aluminum platter and a high-density MDF low profile base are included as standard features of the B-Sharp. Like the C-Major, the B-Sharp uses a high-tech TPE (thermoplastic elastomers) suspension system that works in concert with adjustable feet that provide levelling ability for the table.
- Comes equipped with a factory installed Ortofon 2M Blue Cartridge, hinged dustcover, low mass aluminum record clamp, and a felt platter mat-all included.
|
- Ultra lightweight plinth: The Planar 8 is the second Rega turntable constructed using the latest ultra lightweight Tancast 8 polyurethane foam core (a material developed for the aerospace industry). This material is sandwiched between two layers of HPL (high-pressure laminate). HPL is exceptionally thin and extremely rigid. This new construction makes the new Planar 8 skeletal plinth 30% lighter than the original RP8 while offering increased rigidity over the previous model.
- Double Brace Technology: A super lightweight plinth combined with a phenolic resin double brace mounted specifically where the increased rigidity is required (between the tonearm mounting and the main hub bearing) forms a structurally sound a oestressed beam" assembly. This rigid plinth design prevents energy absorption and unwanted resonances which will add unnatural distortions to the music. Equally, heavier mass can transfer more unwanted energy such as motor or bearing noise directly into the rotating record. The use of braces instead of the complete skin allows double thickness phenolic resin in these key areas while providing further weight reduction to the plinth, which directly addresses the issue of mass absorption and unwanted energy transmission.
- RB880 Tonearm: For the new RB880, Rega has introduced an improved vertical bearing assembly constructed using an aluminum and stainless-steel, low mass assembly with vastly improved stability and rigidity. This tonearm is using their advanced preloaded zero tolerance bearing assembly adjusted to less than 1000th of a mm, this gives friction-free movement and zero levels of unwanted play. This subtle but effective new structure is only visible via small windows at the rear of the new bias housing assembly. A thinner stainless steel balance weight is used, allowing greater adjustability and compatibility. Finally, the RB880 is terminated with a re-designed, low capacitance phono cable terminated with high quality, locking phono plugs to ensure the best possible connection.
- Hub bearing assembly: The Planar 8 uses a new low mass central bearing assembly. A single piece machined aluminum sub-platter and hardened tool steel spindle run inside a custom brass housing which is cleverly mounted within the chassis. This new mounting is designed to eradicate unwanted potential energy being transferred or stored in the plinth.
- Super flywheel effect triple layer glass platter: The Planar 8 uses a three-piece laminated glass platter which is the result of collaboration with a British glass engineering company. This brand new platter is constructed from two different high quality Pilkington glasses. As a general rule, the only part of a turntable that requires extra mass is the turntable platter in order to achieve constant rotational speed. However, a heavier platter creates more problems for the main bearing design so again an ideal compromise creates the best solution. Practically this means keeping as much of the mass to the outside rim of the glass platter to create more flywheel effect but keeping the inside of the platter as light as possible without sacrificing stiffness.
- 24v Low noise motor assembly: The Planar 8 uses Rega's latest generation, 24v, synchronous, low vibration motor technology. Uniquely mounted using the highest level of coupling while retaining higher vibration isolation than any previous model. This new motor mounting technique (mounted from the bottom) has been taken directly from the ultimate Rega turntable, the Naiad. This unique mounting method removes all stress on the motor body. The reduced vibration and more rigid mounting delivers superior drive from the new EBLT drive belts. Each motor is hand tuned to match its own custom Neo power supply before fitting to the turntable to optimize the anti-vibration circuit.
- EBLT Drive Belts: For three years Rega has been researching and developing with chemists the use of a bespoke new rubber compound for drive belts. Using a specialized curing system, the new drive belt offers superior consistency of modulus (a constant representing the degree to which a substance has a particular property, especially elasticity). These new belts are manufactured on Rega designed, state of the art, super-accurate tools which produce 'perfectly round' and 'dimensionally accurate' belts, critical for perfect speed stability.
| The Prime is designed to offer hi-end sound while taking advantage in improvements in Turntable technology. The shape is designed to have a more aesthetic look, while having the footprint to accommodate the space needed for a 10 inch 3D arm.
- 10-inch 3D Tonearm
- VTA Tower included
- Classic 20-pound platter and bearing
- Four solid Delrin corner assemblies designed for isolation and mechanical grounding
|
Reviews
There are no reviews yet.